• <acronym id="kkoye"><tbody id="kkoye"></tbody></acronym>
    首  頁  |  English  |  中文
    產品服務           公司信息            新聞中心           聯系我們
         首 頁 > 產品服務 > POE
     
    EVA膠膜
    白色EVA
    POE
    白色POE
     
    POE      
     

    3M™ Solar Encapsulant Film PO8510
    Polyolefin Encapsulant for Photovoltaic Modules

    Introduction                                                    
    3M™ Encapsulant Film PO8510 offers protection against UV aging and weathering – while enabling maximum  visible light transmission to solar cells with UV cut-off wavelength350 nm (see graph below).

     

     

    Features

    Conformable and flexible for ease of lamination

    Durable bonding strength with both glass and backsheet

    Excellent UV and damp-heat stability

    Very low shrinkage rate

    High light transmission

    No acetic acid/No corrosion

    1/10th MVTR vs. EVA

    Good compatibility with CIGS Modules

    >130°C Creep

    No transmission loss after aging (>1000 hrs)

    Typical Physical Properties (data not for specification purposes)

    Storage

    Shelf life is 6 months under proper storage conditions. The product should be stored indoors with the temperature controlled between 0°C and 30°C and relative humidity below 60%, avoiding direct sunlight. The product should not be placed near any heating equipment or exposed in a dusty place. Check the package box of stored product before unfolding. The product should be used up as soon as possible after the package is unfolded. Any unused product should be properly sealed with original package or similar package.

    Suggested Laminating Conditions

    Vacuum time and temperature in the laminator are very critical for final properties. Use of thermocouples is suggested to monitor the temperature to achieve the right gel percentage.

    DSC and DMA can be used for designing the appropriate lamination cycle if temperature and time are other than the suggested conditionslisted above.

    For optimum performance, gel percentage is recommended to be ideally between 70% to 85%.

    Contact 3M for additional information.

    Precautionary Information

    Refer to the product label and Material Safety Data Sheet for health and safety information before using this product. For additional health and safety information, call 1-800-364-3577 or (651) 737-6501.

     

     

    3M™ Solar Encapsulant Film PO8100N
    Polyolefin Encapsulant for Photovoltaic Modules

    Introduction

    3M Solar Encapsulant Film PO8100N is a fast cure thermosetting encapsulant designed for high efficiency solar cells in PV modules that enable higher transmission of ultraviolet and visible light to increase module power output(see graph below)                                                   

                                                                

      

     

    Features

    Conformable and flexible for ease of lamination

    Durable bonding strength with both glass and backsheet

    Excellent UV and damp-heat stability

    Very low shrinkage rate

    High light transmission

    No acetic acid/No corrosion

    1/10th MVTR vs. EVA

    Good compatibility with CIGS Modules

    >130°C Creep

    No transmission loss after aging(>1000 hrs)

    Typical Physical Properties (data not for specification purposes)

    Storage

    Shelf life is 6 months under proper storage conditions. The product should be stored indoors with the temperature controlled between 0°C and 30°C and relative humidity below 60%, avoiding direct sunlight.The product should not be placed near any heating equipment or exposed in a dusty place. Check the package box of stored product before unfolding. The product should be used up as soon as possible after the package is unfolded. Any unused product should be properly sealed with original package or similar package.

    Suggested Laminating Conditions

    Vacuum time and temperature in the laminator are very critical for final properties. Use of thermocouples is suggested to monitor the temperature to achieve the right gel percentage.

    DSC and DMA can be used for designing the appropriate lamination cycle if temperature and time are other than the suggested conditions listed above. For optimum performance, gel percentage is recommended to be ideally between 70% to 85%.

    Contact 3M for additional information.

    Precautionary Information

    Refer to the product label and Material Safety Data Sheet for health and safety information before using this product. For additional health and safety information, call 1-800-364-3577 or (651) 737-6501.

     

     

     
    關于我們   |   產品服務   |   聯系我們   |   網站地圖   |    滬ICP備14038709號-1 © Copyright@ 2016 上海常必鑫新能源科技有限公司 All Rights Reserved       
    奇米影视网-777奇米影视第四色-奇米影视四色首页-奇米影视电影